SECO-LARM Enforcer E-9679-8B190Q Indoor/Outdoor Long-Range Barrier Sensors, 8-Pairs of Beams

SECO-LARM Enforcer E-9679-8B190Q Indoor/Outdoor Long-Range Barrier Sensors, 8-Pairs of Beams

Add Security to Your Property with Long Range Outdoor Sensors
  • 8 Pairs of Beams, 79" (201cm), Up to 380ft (120m) range
  • For indoor or outdoor perimeter security
  • Install on windows, doorways, skylights, fence tops, and any place where space is limited
  • End caps swivel so sensor can be mounted on single or on opposite walls with no L-bracket needed
  • Programmable trigger
  • Heater for use in cold weather operation
  • Heater activates at 41



List Price: $1,599.30

Your Savings: $801.30

REWARDS: 798 points
  • Details
  • Specs
  • Reviews
  • What's Included
  • ENFORCER Long-Range Barrier Sensors are ideal for protecting indoor or outdoor areas separated by long distances. They feature reliable photobeam technology with a choice of four programmable beam frequencies that provide superior perimeter protection by eliminating crosstalk and interference when multiple units are used. False alarms caused by animals, falling leaves, poor weather, or other sources are minimized by programming the alarm output trigger operation.

    ENFORCER Long-Range Barrier Sensors work in even the most extreme conditions. A built-in heater automatically turns on and off depending on the outside temperature. An environmental control system senses a slow degradation in beam strength when weather conditions worsen to help prevent false alarms.

    Installation and alignment is quick and easy with the ENFORCER Long-Range Barrier Sensors. They come with swiveling heads that allow them to be mounted along the same wall or on opposite walls, as well as provide for easy alignment of the beams between the transmitter and receiver.

    Additional Features
    • Slim design: 2-1/4" x 1-7/8" (55 x 49 mm)
    • Rugged aluminum construction
    • Built-in tamper switches, one on either end, trigger the alarm if end cap is removed
    • No synchronizing wires required to align the beams
    • Form C relay output
    • LED and buzzer alignment indicators
    • AGC (Auto Gain Control) circuits regulate beam signals in order to compensate for and ensure operation in rain, fog, and
    • low-temperature conditions
    • Programmable for 4 different frequencies to reduce interference between multiple units

  • Manufacturer: SECO-LARM
    Brand: Enforcer
    Manufacturer Product No.: E-9679-8B190Q
    UPC: 676544014515
    Number of beams: 6 pairs
    Max. range outdoor: 190' (60m)
    Max. range indoor: 380' (120m)
    Voltage: 12~24VDC
    Tx standby & active current, heater off (+/-25%@12VDC): 100mA
    Rx standby current (buzzer off),heater off (+/-25%@12VDC): 95mA
    Rx trigger current (buzzer on) heater off (+/-25%@12VDC): 95mA
    Buzzer active current (Rx only): [email protected]
    Heater active current (Rx+Tx): [email protected]
    Input voltage: 12~24 VDC
    Response time (receiver): 150/300/450/600 ms (DIP switch programmable)
    Detection methods: Triggers as programmed when any 2 adjacent pair of beams are broken, or any single pair of beams is broken for over 2 sec. (programmable by JP2)
    Selectable beam frequencies: 4 Different frequencies (DIP switch programmable)
    Alarm output: NO/NC/COM, relay output, active for 1 sec. when triggered
    Tamper output (Tx & Rx): [email protected] / [email protected]
    Alignment LED (Rx only): Red LED, ON - beam is broken / OFF - aligned
    Alignment angle: Horizontal +/-90°
    Operating Temperature: -49°~131°F (-45°~55°C)
    Humidity: 95%
    Weatherproof: IP65
    Case: Aluminum housing / PC anti-UV cover / ABS end caps
    Length: 43" (109cm)
    Width x Height: 1-7/8"x2-1/4" (49x55 mm)
    Weight (Tx & Rx) with brackets: 14.3-lb (6.5kg)

  • Leave a Review

    Only registered users can write reviews. Please, log in or register

    • 1x - Transmitter
    • 1x - Receiver
    • 1x - Manual
    • 4x - Pole mount brackets
    • 8x - Machine screws 4x6mm (for pole mount brackets)
    • 8x - Machine screws 4x25mm (for pole mount brackets)
    • 12x - Screws 6x20mm (for wall mount use)
    • 12x - Plastic anchors (for wall mount use)

Please wait...