Insteon Remote Control In-Line Dimmer Switch

Save $5
InsteonSKU: 2475DA1
filler

Multi-Pack Savings Available: Each
Price:
$49.99 $54.99

Description

This dimmer is designed to be installed within a junction box or in a ceiling fixture allowing you remote control over lights that may not have a direct connection to a wall switch. This allows you to pair the dimmer with any number of Insteon remote controllers.

This dimmer controls incandescent bulbs. If you need to control a fluorescent light fixture or an appliance, try the In-Line Relay.

Insteon also offers a Micro Dimmer Module that wires in behind your existing switches or fixtures. This allows you to keep your existing antique, toggle or decorative wall switches while adding the customizable, dimmable Insteon remote control functionality.

Note: As with all dimmers, the In-LineLinc may feel warm during operation. Rigorously tested and approved to UL-standards, the amount of heat generated falls well within approved limits and poses no threat to your home or the lifespan of the device.

Easy To Install

The Insteon In-Line Dimmer is easy to install and set up. Its small size allows installation in a standard J-box or in a ceiling light fixture. Control each kitchen light individually or rows of can lights with a single Insteon In-LineLinc Dimmer. Learn more about Insteon here.

Perfect for Locations without a Switch

Whether you're planning to install recessed lighting or have already done so, you don't need to go through the hassle of running the wiring for a new wall switch. By installing an In-LineLinc in a fixture box, you'll be able to control the lights from any location in your home. Simply install the In-LineLinc in the fixture box, link it manually or via HouseLinc - Insteon Desktop Software, and you'll be able to turn lights on and off and dim them using any Insteon -compatible controller. For maximum personalized control, wire an In-LineLinc to each non-switched light for the ultimate in mood settings.

Adjustable Ramp Rate

Adjust the speed at which the controlled light turns on or off, also known as the ramp rate. For example, you may want the light in the stairwell to turn on instantly so you can see where you're walking. Alternatively, you may want the light in the master bathroom to ramp up in a soft, gentle fashion so you're not blinded in the middle of the night. The ramp rate is adjustable between 0.1 second and 9 seconds if programmed locally. The ramp rate can extend up to 8 minutes (for a simulated sunrise or sunset) if programmed using software such as HouseLinc. This is a great addition to your morning alarm, slowly turning the light on to help you wake up.

Easy to Program

Programming an In-LineLinc can be easily done a couple of different ways. The Tap method is best for your initial setup. Simply go into linking mode on any Insteon -compatible controller and then press the set button on the In-LineLinc for 3 seconds; the load and the status LED will flash. You are now linked and can control the In-LineLinc from the controller of your choice. Keep in mind that once installed in a fixture, the In-LineLinc will not be easily accessible, thus making new links and scene programming difficult. We recommend using software such as HouseLinc 2 - Insteon Desktop Software to manage the links of your In-LineLinc after it is installed. Remember, you will need to have the Insteon ID in order to program with software.

Scene Lighting

Scenes allow you to control multiple lights, rooms or even the whole home with a single command. Because the In-LineLinc Dimmer can be a member of more than 400 scenes (i.e. "Movie Time," "Party," "Romance," etc.), you'll be able to launch various lighting scenarios with a single button press. These are elegant features usually found only in systems costing tens of thousands of dollars and requiring extensive rewiring of your home. All member lights can ramp to your independently desired brightness levels at your chosen ramp rate(s). So one set of lights can dim slowly, while another set turns off instantly, all controlled with one command from one button. If you want to control multiple scenes from one controller, we suggest the Insteon KeypadLinc.

Dual-Band

In-Line Dimmer is dual band so it has the ability to communicate using both the electrical wires in the home (powerline) as well as using radio frequency (RF). This increases reliability not only for In-LineLinc but for all devices on an Insteon home control network (similar to the function of an Access Point).

Non-Volatile Memory

All In-LineLinc Dimmer settings are stored in non-volatile memory and are not lost during power failures. Additionally, in the event of a power loss, the In-LineLinc Dimmer will return to its last brightness level when power is restored.

General
Manufacturer Insteon
Manufacturer Product No. 2475DA1 - (Each)
2475DA1-5PK - (5-Pack)
UPC 813922012361 - (Each)
813922019599 - (5-Pack)
Patent No. U.S. Patent No. 7,345,998. Protected under U.S. and foreign patents (see www.insteon.com)
Safety Approval(s) ETL (Intertek Testing Services)
Certifications FCC, IC Canada
Warranty 2 Years
Insteon Features
On-Levels 32 locally, increments of 1% with software
Ramp Rates (full-On to full-Off) 0.125 to 9 seconds if programmed locally, 0.125 seconds to 8 minutes if programmed remotely
Operation modes Insteon
LED indicator Green when load is On
Red when load is Off
Multi-Way Circuit Support Yes, as a receiver and as a controller
Setup Memory Non-volatile EEPROM
Insteon ID 1
Insteon Groups 400 responder groups and 1 controller group
Maximum Scene Memberships 400 (combined controller and responder)
Scene commands supported as responder On | Off
Fast-On | Fast-Off
Brighten | Dim
Software Configurable Yes
Ramp Rates (full-On to full-Off) 0.125 to 9 seconds if programmed locally,
0.125 seconds to 8 minutes if programmed remotely via software
RF Range 100 ft.(depending on your home’s construction)
Mechanical
Mounting Mounts inside standard electrical box in the ceiling or in the wall
Wire's White - Neutral 18 gauge
Black - Hot 16 gauge
Red - Load 16 gauge
Copper - Earth ground 14 gauge
Beeper Yes
Dimensions(H x W x D) 2.75" x 1.75" x 1"
Weight 2.5 oz
Storage Conditions 4-158°F (-20-70°C)
Electrical
Voltage 100-277VAC +/- 10%, Single phase
Frequency 50/60Hz auto-detected at power-up
Load Types 15A/240VAC
3600W/240VAC resistive
700W/240VAC inductive/capacitive
2000W/240VAC bulbs/low voltage halogen
Load Types Wired-in incandescent lighting
Maximum Load 400 Watts
Retain All Settings Without Power Yes, saved in non-volatile EEPROM
Standby Power Consumption <1W
  • 1x - Insteon In-Line Dimmer
  • 1x - Quick Start Guide
  • 4x - Wire Nuts

Customer Reviews

Based on 40 reviews Write a review

Payment & Security

Amazon American Express Apple Pay Discover Google Pay Mastercard PayPal Venmo Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

You may also like

Recently viewed