Insteon DIN Rail On/Off
Share Share Share Share Share

Insteon Remote Control DIN Rail On/Off Switch

Manage Complex Wiring Circuits with DIN Rails and the Insteon DIN Rail On/Off
  • Simply clip onto 35mm DIN rail and wire like any other Insteon switch
  • Optional sense wires allow for control via a connected, hard-wired switch
  • Compatible with latching, single momentary and dual momentary switches
  • This product is an Insteon Dual-Band device
  • Works with Amazon Alexa for voice control (Insteon Hub required; Alexa device and Insteon Hub each sold separately)

Item #: 2453-222 IN STOCK - SHIPS TODAY

REWARDS: 49 points
Frequently Bought Together:
  • Details
  • Specs
  • Reviews
  • Manuals
  • What's Included
  • When planning the electrical wiring for your home or business, avoid adding too many wall switches in a single location. Wall switches ganged together cause homeowner confusion and can quickly ruin the aesthetic of a room. Instead consider adding a single Insteon keypad to control all the lighting. It's easy when combined with Insteon DIN Rail products.

    For a professional finish to your DIN Rail installation, consider using an Indoor/Outdoor DIN Rail Enclosure with Pre-Installed DIN Rails(s). Optionally, individual DIN Rails and Enclosures are available separately.

    Use of DIN rails is common overseas and in US commercial/industrial buildings. Because of their ease of installation, DIN rails are becoming more popular in the US. DIN rail products provide integrators and builders a more custom and organized way to handle complicated wiring circuits.

    The DIN Rail On/Off clips directly onto a 35mm DIN rail and wires to load, power and neutral. Link it to an Insteon keypad or any other Insteon device for full remote control over the module and it's connected load. Specifically, DIN Rail On/Off is compatible with the "Top hat rail EN 50022" (sometimes referred to as a Type O or Type Ω) The DIN Rail On/Off will fit either variation of this style DIN rail (either 15 or 7.5 mm "high" off the mounting surface).

    What's a DIN Rail?
    It is simply a metal rail on which compatible products (circuit breakers, switches, etc.) can be snapped on. The DIN rail can simply be mounted to any flat surface (or even across studs). Please follow all applicable building and electrical codes whenever installing electrical products.
    Top hat DIN rail Cross section With module snapped on

    Please note that the DIN Rail On/Off is not compatible with C section or G section Din rails.

    Optional Sense Wire Trigger
    The DIN Rail On/Off features sense inputs for special applications where a local "dumb" switch might be necessary in addition to remote Insteon control. Sense inputs are compatible with latching, single momentary and dual momentary wall switches. Connect to any style wall switch to match any type of designer theme (antique, push-button, metal, etc.)

    Local Control and Insteon Setup
    The DIN Rail On/Off has a small paddle that operates exactly the same as the best-selling SwitchLinc paddles. So, you can turn the connected load on or off by tapping the paddle. Furthermore, a setup button is provided for setting up other properties as well as for linking and un-linking. Finally a dual-color (green and red) LED displays the on (green) or off (red) status of the connected load.

  • General
    Manufacturer Insteon
    Product Name DIN Rail On/Off
    Manufacturer Product No. 2453-222
    UPC 813922012828
    Warranty 2 Years
    Insteon Features
    Operation Modes Controller and responder
    Maximum Links/Scenes 400
    Load Brightness Levels 32 locally (256 with software)
    Status LED Green when load is on, Red when load is off
    Blinks Red once when responder does not acknowledge/blinks
    Green once if all responders acknowledge (can be disabled via software)
    Blinks Green or Red during setup
    Blinks Red or Green (depending upon state of load) to indicate traffic (must be enabled via software)
    LED Brightness Adjustable from off to 100% bright
    Local Control Yes
    Commands Supported s Controller On | Off
    Fast On | Fast Off
    Begin Brighten | End Brighten
    Begin Dim | End Dim
    Commands Supported as Responder On | Off
    Fast On | Fast Off
    Software Configurable Yes
    RF Range 150 ft. (depending on your home’s construction)
    Phase Detect Beacon Yes
    Insteon Device Category 0x02 switched lighting control (all frequencies)
    Insteon Device Subcategory 2453-222 (915MHz) | 0x2E
    Mounting 35mm (top hat) DIN rail
    Wire Connections N/A
    Max. Cable Size 4mm², 12 AWG (2.72mm diameter)
    Min. Cable Size 1.5mm², 15 AWG
    Screw DIN Rail Connections Line
    Sense 1
    Sense 2
    Case Color White
    Set Button Yes
    Plastic UV stabilized polycarbonate
    Beeper Yes
    Beep on Button Press Optional (off by default)
    LED 1 RGB
    Dimensions 3.14" x 2.05" x 2.48"(H x W x D)
    Weight 6.17 oz (175g)
    Operating Environment Indoors
    Operating Temperature Range 32° to 104°F (0° to 40°C)
    Operating Humidity Range 0-90% relative humidity
    Storage Temperature Range -4° to 158°F (-20° to 70°C)
    Voltage 100VAC to 240VAC
    Frequency 50/60Hz auto-detected at power-up
    Load Types Resistive
    Low voltage halogen
    Low voltage halogen
    User Replaceable Fuse Yes, (16 A (T)) 5x20mm fuse
    Hardwired Remote Control Yes, either latching or momentary switches supported
    Retain All Settings Without Power Yes, saved in non-volatile EEPROM
    Standby Power Consumption <1W
    Safety Approved ETL
    Certifications FCC
  • 8 Reviews

    Review of 2453-222 Review by JOSENIVALDO
    Review of 2453-222

    The DIN form factor is very good to install on the power distribution panel or in the attic.

    Posted on 5/3/2014

    Review of 2453-222 Review by JOSEPH
    Review of 2453-222

    Does what it's meant to do. And with this configuration it is easy to install

    Posted on 10/10/2013

    Review of 2453-222 Review by DON
    Review of 2453-222

    I like din rail stuff, but it would be cool if it was dual band!

    Smarthome response: You're in luck! The DIN Rail is in fact a dual-band INSTEON device.

    Posted on 8/9/2013

    Review of 2453-222 Review by GUILLERMO
    Review of 2453-222

    Great product to lead to homeautomation. We need am inwall LCD that controls everything that could go a step closer to vantage or lutron

    Posted on 7/17/2013

    Review of 2453-222 Review by GUILLERMO
    Review of 2453-222

    I'm building the systems now with this module. Great product

    Posted on 5/16/2013

    Review of 2453-222 Review by DAVID
    Review of 2453-222

    Works great. Be aware the sense inputs can not be used for anything other than a latching circuit.

    Posted on 5/5/2013

    Review of 2453-222 Review by JOHN
    Review of 2453-222

    Exactly what I needed!

    I have a large house, and with water prices rising I installed a water recirculation system to use less water waiting for hot water to get to fixtures. I used one of these to trigger the circulation pump on ONLY when some one turns on bathroom lights. (4 bathrooms) I installed it in an over size enclosure with a short piece of DIN rail, the pump also has a thermostat. I've already seem our water usage drop by about 15 gallons per day.

    Posted on 1/20/2013

    Review of 2453-222 Review by JOSEPH
    Review of 2453-222

    Good product

    Posted on 1/20/2013

    Leave a Review

    Only registered users can write reviews. Please, log in or register

    • 1x - Insteon Din Rail On/Off
    • 1x - Quick Start Guide

Please wait...