Advector inVent-M/C-R1 inVENT Manually Adjustable Register for New Construction

Advector inVent-M/C-R1 inVENT Manually Adjustable Register for New Construction

Stop Heating and Cooling Empty Rooms and Evenly Balance the Temperatures in Your Home
  • Adjust the air flow to lower HVAC system run time, reducing your monthly energy bill
  • Replaces old vents and performs better, looks better, and adds value to your home
  • Typical installation takes less than thirty minutes and with little more than a screwdriver
  • 360° airflow pattern means no more direct drafts from your HVAC vents
  • Specially engineered design and material selection help reduce the sound from the duct system and the air noise exiting the vent


REWARDS: 15 points
  • Details
  • Specs
  • Reviews
  • Manuals
  • What's Included
  • We all struggle with those rooms that never get the right amount of air and end up feeling much too cold or way too hot.. But if you are not ready for a fully automated HVAC system...then the Advector inVent-M/C-R1 inVENT Manually Adjustable Register for New Construction might be just what you need. Using aerodynamic principles to promote 360 degree airflow distribution, the Manually Adjustable inVENT provides for more comfortable and balanced feeling temperatures. The inVENT closing plate has a full range of motion between the open and closed position allowing you to decide how much conditioned air is directed at each room. Adjust the closing plate to the shut position and stop wasting money heating and cooling empty rooms...adjust the closing plate to the open position to redirect the conditioned air to where you need it most. The manually adjustable inVENT gives you the ability to regulate temperatures by controlling the amount of air that enters each room.

    This product is also available for , sold separately.

    Additional Features
    • Quickly make adjustments to room temperatures to address changes in the weather or room occupancy.
    • The aerodynamic design causes the air to grip the ceiling, wall, or floor to maximize air distribution and comfort
    • Lower your energy usage without having to spend a fortune

    • Please Note: It is recommended that you install the Advector Duct Transition prior to installing sheet rock.

    Performance Data
    Closing Plate Position CFM Flow Rate --> 50 100 150 200 250 300 350
    Fully Open Static Duct Pressure --> 0.05 0.09 0.14 0.22 0.34 0.57 0.73
    Fully Open Duct Diameter --> 8-inch 8-inch 8-inch 9-inch 9-inch 9-inch 9-inch
    Fully Open Noise Criteria --> - 19 27 34 42 50 62
    Fully Open Horizontal Face Velocity --> 620 1180 1520 1900 2320 2733 3125
    Fully Open Horizontal Throw --> 7 16 22 32 41 51 58

    Performance Notes
    • Airflow is in cubic feet per minute.
    • All pressure is measured in inches of water
    • Duct Static Pressure is based on 8inch and 9inch duct sizes as indicated
    • Face Velocity is in feet per minute
    • Horizontal Throw is calculated based on 50fpm air velocity and 360 degree distribution pattern
    • inVent cfm rate can be fully controlled by closing and opening of the Closing Plate
    • The Noise Criteria values are based on a room absorption rate of -10 db, referenced to 1pW and one inVENT

  • Specifications
    Manufacturer Advector
    Manufacturer Product No. inVent-M/C-R1
    UPC 857309003009
    Base Diameter 10.4in
    Profile height at full open 1.6in
    Profile height at full close 0.9in
    Weight 0.6lbs
    Primary Material ABS Plastic
    Surface Finish White, textured

  • Leave a Review

    Only registered users can write reviews. Please, log in or register

    • 1x - Advector inVent-M/C-R1 inVENT Manually Adjustable Register for New Construction
    • 3x - #10 mounting screws
    • 1x - Gasket
    • 1x - Twist Ring
    • 1x - Owner's Manual

Please wait...