Venstar ACC-TSEN Remote Indoor/Outdoor Air Temperature Sensor for ColorTouch Thermostat
Share Share Share Share Share
Rewards: 30 Points

Venstar ACC-TSEN Remote Indoor/Outdoor Air Temperature Sensor for ColorTouch Thermostat

Send a Temperature Reading to a ColorTouch Thermostat
  • Sensor used to transmit temperature to ColorTouch Thermostat
  • Ideal for indoor or outdoor installation
  • -20 - 120° temperature range

Item #: 30454

In stock - Ships Today

Special Price: $15.39

List Price: $26.00

Your Savings: $10.61

Frequently Bought Together:
+

Venstar ACC0454 Skyport Wi-Fi Key for ColorTouch Thermostats

Special Price: $59.97

List Price: $99.99

Your Savings: $40.02

Price For Both: $75.36

  • Details
  • Reviews
  • Manuals
  • What's Included
  • The Venstar ACC-TSEN Remote Indoor/Outdoor Air Temperature Sensor measures indoor or outdoor air temperature with a range of -20 to 120° F. If used indoors as a remote temperature sensor, the sensor will read room temperature and send the information to the ColorTouch thermostat. If used as an outdoor temperature sensor, the sensor may be used to provide outdoor temperature information (which is not used to control heating or cooling). The Air Temperature Sensor should be mounted out of direct sunlight and in a place that is protected from direct rain and snow. Mounting the sensor under an eave of a roof or under an overhang of a building is recommended. Connect the Remote Sensor using 18 - 22 gauge 2 conductor unshielded thermostat wire not to exceed 200 feet.


    Outdoor Locations
    The Venstar Indoor/Outdoor Remote Temperature Sensor should be mounted on the north side of the building, out of direct sunlight, and in a place that is protected from direct rain and snow. Mounting the sensor under an eave of a roof or under an overhang of a building is recommended. If the Outdoor Sensor is mounted on a rough surface, it is recommended that silicon rubber sealant be used around the entire edge of the mounting plate. If mounting on an electrical junction box, be sure the seal between the junction box and sensor mounting plate is tight.

    Indoor Locations
    The Venstar Indoor/Outdoor Remote Temperature Sensor should be mounted approximately five feet from the floor, close to or in a frequently used room, preferably on an inside partitioning wall or on a section of wall without pipes or ductwork. Mount the sensor where temperature operating limits are within 32° F to 99° F and where humidity operating range is within 0% to 95% relative humidity, non-condensing.

    Incorrect Locations
    The Venstar Indoor/Outdoor Remote Temperature Sensor should NOT be mounted close to a window, on an outside wall, or next to a door leading to the outside. Do not mount the sensor in a location where it would be exposed to direct light and heat from a lamp, the sun, a fireplace, or any other temperature-radiating object which may cause a false reading. Finally, do not mount the sensor close to or in direct airflow from supply registers or return air grilles and in areas with poor air circulation (such as behind a door or in an alcove).
  • 6 Reviews

    Review of 30454 Review by JEFF
    Review of 30454
    Rating

    I returned this item due to unacceptable quality of the T6800. Have not installed, forced to rate to submit other reviews.

    Posted on 2/2/2014

    Review of 30454 Review by THOMAS
    Review of 30454
    Rating

    Not yet installed as I need one additional wire that might be difficult to run.

    Posted on 11/28/2013

    Review of 30454 Review by KEVIN
    Review of 30454
    Rating

    Have not installed yet; it requires a hard-wired connection to the sensor. I'll get to that later.

    Posted on 1/18/2013

    Review of 30454 Review by DAN
    Review of 30454
    Rating

    Easy to install and does what it's supposed to do. No problems at all.

    Posted on 1/9/2013

    Review of 30454 Review by STENNETT
    Review of 30454
    Rating

    Sensor works well. It was very easy to install and the outdoor temp showed up as soon as it was connected. Very pleased.

    Posted on 7/11/2012

    Review of 30454 Review by MIKE
    Review of 30454
    Rating

    Easy to install, good and simple directions.

    I installed this in conjunction with a Venstar T5800 T-stat - as soon as the sensor was connected, the outside temperature reading was there on the T-Stat screen, and it was a believable reading.

    Posted on 7/28/2011

    Leave a Review

    You're reviewing: Venstar ACC-TSEN Remote Indoor/Outdoor Air Temperature Sensor for ColorTouch Thermostat

    • 1 star
      2 stars
      3 stars
      4 stars
      5 stars

    * Required Fields

    • 1x - Remote Indoor/Outdoor Air Temperature Sensor


place your order by 3pm PT for same day shipping

Please wait...

smarthome

Item has been added to your cart
smarthome

Item has been removed from your cart