- What's Included
Similar dimmers are up to 50 percent deeper than X10 Wall Switch. With its slim design, installation is easy, even in small junction boxes.
Easy to Install and Set Up
This switch wires in like a standard wall switch with an additional connection to a neutral wire. To set the X10 address, press & hold the Set button until it beeps and then send the X10 address from any X10-compatible transmitter.
Built with a Quieter Relay
Because X10 Wall Switch is built with a much quieter relay than most remote-control switches, it has a click that is 80 percent quieter than traditional relay switches. This allows you to control lights and other non-dimmable devices without waking up the baby, annoying other family members, or sending your cat fleeing across the room. The click of the internal relay is barely audible.
Generates Less Heat
Unlike other switches, X10 Wall Switch uses a relay to control the load. Other switches use components that absorb about two volts of power and dissipate the heat through the front of the switch. By using a relay, the switch runs cooler and full voltage gets to the load.
Create Multi-Way Circuits
The X10 Wall Switch allows you to customize your setup no matter how your house is wired. Create a brand new circuit or add to an existing one. Simply replace all of the existing switches you want to include in the circuit. If adding to an existing multi-way circuit, use the same X10 address assigned to the current switches. If you are creating a new circuit, choose one address and program it to each one of the switches. No traveler wires or additional programming is needed.
All X10 Wall Switch settings are stored in non-volatile memory and are not lost during power failures. Additionally, in the event of a power loss, X10 Wall Switch will return to its last brightness level when power is restored.
Smarthome warranties this product for 90 days.
Safety Tested and Factory Certification
All Smarthome products are safety approved. The assembly line for Smarthome Design Products is ISO9002 certified. In order to meet the ISO 9002 standards, the entire factory underwent rigorous inspections of procedures and policies before being thoroughly audited. The certification received was based on its dedication to high quality management systems and strict adherence of quality systems and guidelines.
The paddle can easily be changed out to match your d
General Brand: Smarthome Manufacturer Product No.: X10WS13A, Smarthome X10 Decorator Style Switch Warranty 90 Days Operation LED Indicator One Amber LED Multi-Way Circuit Support One Dimmer Switch controls load, add any number of additional X10WS13A Switches (only connect to LINE and NEUTRAL) and program with same X10 address Setup Memory Non-volatile EEPROM Mechanical Paddle Type True rocker action Paddle and Trim Frame Color White installed, Optional Ivory, Almond, Black, Brown, or Grey (sold separately) Wire Nuts 4 included Mounting Mounts in single or multiple-ganged junction box. Operating Conditions Indoors, 32 to 104°F, up to 85% relative humidity Dimensions 4.1" H x 1.8" W x 1.2" D Weight 3.6 oz l Electrical Supply Voltage 120 Volts AC +/- 10%, 60 Hertz, single phase Power Wire Leads 6", 16 AWG, stranded, 600V, 105°C insulation, ends stripped and tinned, LINE (black), LOAD (red), NEUTRAL (white) Ground Lead 6", 18 AWG, stranded, bare copper Load Types Wired-in incandescent lighting and inductive loads Maximum Load 10 Amps; 400 Watts (for incandescent loads) Power Consumption: 0.21 Watts Certification Safety tested for use in USA and Canada (ETL #3017581) X10 Features X10 Primary Address 1 optional (comes unassigned) X10 Scene Addresses N/A X10 Status Response Supported X10 Resume Dim Supported (by setting Local On-Level to zero) X10 Powerline Frequency 120 KHz X10 Minimum Transmit Level 3.2 Vpp into 5 Ohms X10 Minimum Receive Level 10 mVpp nominal X10 Messages Repeated No
Leave a Review
- X10 Wall Switch
- 2x - Mounting screws
- 4x - Wire nuts
- Quick-Start Guide