Smartenit EZIO40 INSTEON 4 Output Relay Load Controller
Share Share Share Share Share
Rewards: 218 Points

Smartenit EZIO40 INSTEON 4 Output Relay Load Controller

Control Any Relay-Based Device from your INSTEON Network
  • Four outputs let you control both AC and DC loads
  • Compatible with INSTEON and X10 products
  • Pass through outlet
  • Easy installation takes only minutes

Item #: 31283

In stock - Ships Today

$109.96
Frequently Bought Together:

Price For Both: $159.95

  • Details
  • Specs
  • Reviews
  • What's Included
  • The Smartenit EZIO40 has four independently controlled relay outputs that operate normally opened or normally closed contacts. The four dry-contact relay outputs allow control of low voltage 120 Volt AC (up to .5 Amps) or 24 Volt DC loads. Each relay can be linked individually or with other the other relays on the device as a responder to a group command from an INSTEON controller. The device also has a built-in powerline interface and acts as a repeater of powerline INSTEON signals. Additionally, a programmable timer can be set on each relay to force an off condition providing momentary action from 1 sec to 255 minutes. The simple press of a button from your INSTEON KeypadLinc, RemoteLinc or from your cell phone through a SmartLinc, you can switch loads such as large relays, furnace heaters, blowers, chimes, momentary pushbuttons and more, the possibilities are endless.

    While basic functions can be programmed manually, advanced functionality can be programmed with the EZSrve, central automation controller. If you already have a central automation controller or a software package for your INSTEON network that doesn't have the correct parameters to program the advanced functionality of this device, you can download the free Smartenit Utility Suite which works in conjunction with an INSTEON Powerlinc Modem (2412U, 2413U or 2413S). If you need PC-free operation for simple timers, the Smartenit Utility Suite also interfaces with the INSTEON Powerlinc Controller.

    INSTEON Compatible
    • The EZIO40 Controller is fully INSTEON compatible. INSTEON is a powerful home-control networking technology. INSTEON messages are transmitted throughout your home both wirelessly and through the home's existing wiring. All INSTEON messages are confirmed and repeated by INSTEON devices in the network, contributing to the outstanding reliability and performance of INSTEON products.

    • X-10 compatibility
    • The EZIO40 also works with legacy X10 products. If you have an existing X10 network, the Controller works with your X10 products and provides an upgrade path to an INSTEON network.


  • Specifications

    General
    Brand: Smartenit
    Manufacturer Product No.: EZIO4O, #5010J, INSTEON/X10 Input/Output Module
    UPC: 79357345390
    Color: White
    Warranty: One Year, limited
    Operation
    Status LED: White & Blue
    Setup Memory: Non-volatile EEPROM - up to 30 links
    INSTEON Features
    INSTEON Addresses: 1 hard-coded out of 16,777,216 possible
    INSTEON Links: 417
    INSTEON Powerline Frequency: 131.65 KHz
    INSTEON Minimum Transmit Level: 3.2 Vpp into 5 Ohms
    INSTEON Minimum Receive Level: 10 mVpp nominal
    INSTEON Messages Repeated: Yes
    X10 Features
    X10 Primary Address: 1 optional (requires entire House code - comes unassigned)
    X10 Powerline Frequency: 121 KHz
    X10 Minimum transmit Level: 3.2 Vpp into 5 Ohms
    X10 Minimum Receive Level:
    20 mVpp nominal
    X10 Messages Repeated: No
    Mechanical
    Operating Temperature Range: Indoors, 32 to 104°F
    Operating Humidity Range: 0% - 85% relative humidity
    Dimensions: 4.0" H x 2.5" W x 1.5" D (excluding external valve connector)
    Weight: Approx. 5.0 ounces
    Electrical
    Supply Voltage: 120 Volts AC +/- 10%, 60 Hertz, single phase
    Surge Protection: MOV rated for 150 Volts
    Power Plug: 3-pin grounded
    Pass Through Outlet: 3-pin grounded
    Certification: Safety tested for use in USA and Canada (ETL #3101636)


  • Reviews 1 - 10 of 21

    Page:
    1. 1
    2. 2
    3. 3
    Review of 31283 Review by Aaron
    Review of 31283
    Rating

    As mentioned before... does not work with Insteon Hub!! I actually got it to connect but it would only switch one channel. Too bad, I was hoping to control my pool with this.

    Instructions were not clear and did not specifically say it would not support Insteon Hub.

    Posted on 5/29/2014

    Review of 31283 Review by DICK
    Review of 31283
    Rating

    Does not work with the Insteon Hub. Only useful as a X10 controller

    Posted on 4/26/2014

    Review of 31283 Review by STAN
    Review of 31283
    Rating

    Works as specified. But one "hitch" with the X10 setup: One part of the documentation says to send the desired address and "on" command. However, it fails to mention that you need to do this THREE TIMES. I found this vital missing piece of information in another document... and then finally got the unit configured.

    Posted on 9/7/2013

    Review of 31283 Review by STAN & MICHELLE
    Review of 31283
    Rating

    Works as specified. But one "hitch" with the X10 setup: One part of the documentation says to send the desired address and "on" command. However, it fails to mention that you need to do this THREE TIMES. I found this vital missing piece of information in another document... and then finally got the unit configured.

    Posted on 9/7/2013

    Review of 31283 Review by DON
    Review of 31283
    Rating

    Nice product a little pricey per point but beats the micro module!
    Both this and the irrigation module have a heat issue and seem to run hot. Also the screws on the terminal are very small and difficult to use. and Will not tighten down properly. But for a quick 4 relay output it is great and simple to set up. Perfect interface to the elk 120 voice/siren card!

    Posted on 8/11/2013

    Review of 31283 Review by NEIL
    Review of 31283
    Rating

    Excellent solution when you need more than just N/O and N/C.

    Posted on 5/8/2013

    Review of 31283 Review by KEN
    Review of 31283
    Rating

    Works well with the ISY99.

    Posted on 12/29/2012

    Review of 31283 Review by JEFF
    Review of 31283
    Rating

    Got it to control my loud siren. Works perfectly.

    Posted on 10/4/2012

    Review of 31283 Review by MICHAEL
    Review of 31283
    Rating

    This was a replacement for a unit that failed. I am stuck replacing these units and a lot of indigo modules because of consistant failures. I have whole house surge protection on several sites, and monitor the power from several high end ups units. The problem is not power, the problem is poor quality control. How about respond ing to this and we can discuss how you are taking a good idea and making it unusable.

    Posted on 9/21/2012

    Review of 31283 Review by CLAUDIA
    Review of 31283
    Rating

    Good, work fantastic, I wish a feedback for each relay active in insteon id this posible?

    Posted on 7/18/2012

    Leave a Review

    You're reviewing: Smartenit EZIO40 INSTEON 4 Output Relay Load Controller

    • 1 star
      2 stars
      3 stars
      4 stars
      5 stars

    * Required Fields

    • 1x - Smartenit EZIO40 INSTEON 4 Output Relay Load Controller
    • 1x - Quick Start Guide
place your order by 3pm PT for same day shipping

Please wait...

smarthome

Item has been added to your cart
smarthome

Item has been removed from your cart