Radio Design Labs FP-PA35A 35W Mono Audio Amp 25/70/100V
Share Share Share Share Share
Rewards: 74 Points

Radio Design Labs FP-PA35A 35W Mono Audio Amp 25/70/100V

Be the first to review this product

Power Multiple 25V, 70V or 100V Speakers from a Single Amplifier
  • 35 watts RMS constant voltage amplifier
  • 25, 70, or 100 volt output
  • Automatic energy-saving sleep mode
  • Selectable sleep delay: off, 5, 15, or 25 minutes
  • Input/output terminal block connections
  • Line level balanced or unbalanced input

Item #: 77970

In Stock! SHIPS TODAY!

Special Price: $74.99

List Price: $279.71

Your Savings: $204.72

  • Details
  • Specs
  • Reviews
  • What's Included
  • The FP-PA35A is the ideal choice in many applications where multiple 25 V, 70 V or 100 V speakers in a zone need to be powered from a single audio power amplifier.

    The FP-PA35A features a balanced line level input that may be connected unbalanced. A front panel gain control is designed to be adjusted manually or with a trimming screwdriver. The gain range will accommodate standard unbalanced levels as well as professional balanced levels. Multiple distributed sound system speakers connect to the corresponding 25 V, 70 V or 100 V amplified output.

    The FPPA35A includes an analog compressor/limiter for audio fidelity audibly superior to conventional class D amplifiers with digital limiting. The input GAIN setting determines whether the limiter alone is used for clipping suppression, or if the full compressor/limiter will be used to substantially increase the average output power beyond that of a standard 35 W amplifier. A red COMPRESSION LED flashes when the limiter is preventing output clipping. Normal audio level signals remain unaffected by the compressor thereby preserving audio dynamics. If the input level is increased so that the compressor is active, the LED remains dimly lit between peak flashes. The audio is compressed according to three dynamic time constants providing aural transparency while maintaining clean, unclipped amplified audio for input overloads of up to 20 dB. The FP-PA35A, with compression, is capable of producing average audio output levels and clarity normally expected from amplifiers with a much higher output power rating.

    The FP-PA35A circuits are all designed for low power consumption. In the absence of an audio input, a digital timer is enabled to switch the class D output stage off. When this sleep mode is active, the amplifier module and its included RDL power supply consume less than 1 W of mains power. A front-panel control sets the sleep mode delay timer to 5, 15 or 25 minutes. The control also permits the installer to bypass the sleep mode to conform to system specifications that require the amplifier to be active at all times. Upon detection of an input signal, the amplifier is nearly inaudibly and instantly restored to full operation within 150 milliseconds.

    A blue POWER LED illuminates when the FP-PA35A is powered from its external 24 Vdc power supply. The power LED is dimly illuminated when the sleep mode disables the amplifier and glows brightly when the amplifier operation is fully enabled. The module is equipped with both thermal and output short-circuit protection. The high-efficiency Class D output stage produces minimal heat for all levels of expected voice or music modulation. Continuous full-power operation with audio tones will not damage the amplifier, but is not recommended.


    • Input: Line level(+4 dBu nominal balanced, -10 dBV nominal unbalanced)
    • Input Impedance: 20k Ohms balanced bridging, 10k Ohms unbalanced
    • Input/Output Connectors: Detachable terminal block
    • Gain Adjustment: Single turn audio taper
    • Minimum Input Levels, Balanced: -14 dBu (to cross compressor threshold)
    • Minimum Input Levels, Unbalanced: -15 dBV (to cross compressor threshold)
    • Maximum Input Levels: Balanced +22 dBu, Unbalanced +20 dBV
    • Frequency Response: 50 Hz to 20 kHz (+/- 3 dB)*
    • THD+N: < 0.5% (@ 1 kHz)*, < 0.5% (50 Hz to 20 kHz, 1 W)
    • Compressor: Threshold 2 dB below rated output, automatic adjusting attack and release times
    • Noise: <-75 dB (below 35 W RMS)
    • CMRR: > 60 dB (50 Hz to 120 Hz)
    • Output Power: 35 W RMS @ 25 V, 70 V or 100 V
    • Sleep Mode Power Consumption: < 1 W (amplifier and included power supply)
    • Sleep Mode Delay: 5, 15 or 25 minutes (selectable)
    • Sleep Mode Disable: Selectable
    • Active Mode Delay: < 150 mS after input audio detected
    • Audio Detector Threshold: -50 dBu balanced, -52 dBV unbalanced
    • Ambient Operating Environment: 0° C to 40° C Maximum; 20° C Recommended
    • Indicators (2): Red LED: PEAK LED indicates compressor activity, Blue LED: Power ON, Dim: Sleep mode active; Bright: Amplifier active
    • Power Supply (included): 100 to 240 Vac, 50-60 Hz, 2A; 24 Vdc output to module, Ground-referenced
    • Dimensions: Height: 2.80 in.(7.1 cm); Width: 3.25 in.(8.26 cm); Length: 6.04 in.(15.3 cm)

    *measured at compressor threshold level equaling 22 W RMS output power
  • Leave a Review

    You're reviewing: Radio Design Labs FP-PA35A 35W Mono Audio Amp 25/70/100V

    • 1 star
      2 stars
      3 stars
      4 stars
      5 stars

    * Required Fields

    • FP-PA35A unit
    • Power supply
Norton McAfee
place your order by 3pm PT for same day shipping

Please wait...

smarthome

Item has been added to your cart
smarthome

Item has been removed from your cart