Special Price: $99.99
List Price: $119.00
Your Savings: $19.01
Special Price: $49.99
List Price: $59.99
Your Savings: $10.00
Price For Both: $149.98
- What's Included
Ballast Dimmer - 0-10V Driver
All your commercial dreams come true.
The new INSTEON Ballast Dimmer is two products in one: A 0-10V control module for electronic dimming ballasts and a two-relay control module for traditional non-dimming fluorescent light ballasts. Installed alongside your fixture's existing fluorescent ballast, Ballast Dimmer adds INSTEON control and dimming to a wide range of commercial-centric fluorescent lighting. And the best part: Since INSTEON uses your installations existing electrical wiring for command and control, there's no need to tear up the walls or spend hours in (tight/awkward/precarious) spaces running new electrical wiring.
Shine with 32 Brightness Levels.
Whether your goals are to conserve energy or to add a touch of dimmable elegance, the INSTEON Ballast Dimmer delivers both. Ballast Dimmer can dim electronic dimmable ballasts that respond to a 0-10VDC input signal. Depending on the electronic ballast, you may be able to smoothly dim your fluorescent lights as low as 3%, providing reduced power consumption when a room is unoccupied and helping to create atmosphere with reduced lighting levels.
Your two-for-one relay solution.
No need for dimming? Ballast Dimmer can be configured to operate as a dual-relay switch for non-dimming ballasts, controlling two ballasts with a single module. Depending on your needs, you can use one ballast dimmer to vary the light output in a single large fluorescent fixture, powering only the lamps you need when you need them. Install a single INSTEON switch or keypad and let scenes provide your dim and bright illumination modes. And since Ballast Dimmer is installed per-fixture, your overhead lighting customization is sure to be unique.
Ready for commercial buildings..
Many commercial installations need more than a single split-phase 120V supply can provide. That's why we've built in an auto-detecting, power supply that can handle input voltages from 100-277VAC at 50 or 60Hz. Whatever your building voltage and frequency, Ballast Dimmer has you covered.
Reliable wireless communication.
Ballast Dimmer was built from the ground up with patented INSTEON Dual-Band communications technology, leveraging the best powerline signaling with far-reaching and phase-bridging RF communication. Dual-Band becomes that much more important in multi-phase buildings, making it possible to install Dual-Band INSTEON keypads and switches on entirely different electrical phases.
Control every fixture from a single button.
Ballast Dimmer excels at simplifying your lighting control system. Install a single Keypad Dimmer to control all of the hidden Ballast Dimmers and you won't have to teach someone how to turn the lights on or off. In a conference room, program the Keypad to recall a mode for Presentation that dims all of the overhead fluorescent fixtures, turns off the lights closest to the projection screen and lowers the screen. In a lobby, configure a Keypad to quickly switch between Morning, Day and Afterhours where the overhead illumination intensity responds to business hours, all with no central controller necessary. The Ballast Dimmer can remember 400 lighting scenes each with different light levels and fade on/off rates
General Product Name INSTEON Ballast Dimmer Brand INSTEON Manufacturer Product Number 2475DA2 (US) UPC 813922011432 (US) Patents Protected under US and foreign patents (see www.insteon.com/patents) Warranty 2 Years, Limited INSTEON INSTEON ID 1 INSTEON 400 responder groups and 1 controller group Maximum Scene Memberships 400 (Combined Controller + Responder) INSTEON Device Category 0x01 Dimmable Lighting Control (All Frequencies) INSTEON Device Subcategory 2475DA2 (915MHz 0x25 Load brightness levels 32 locally (256 with software) Status LED Green when load is on, red when load is off LED brightness Adjustable, from off to bright via software Local on-level (Dimming Mode) Adjustable, 32 fixed brightness levels or resume dim Local ramp-rate (Dimming Mode) Adjustable from 0.1 seconds to 9 seconds locally (0.1 seconds to 9 minutes via software) Local control Yes Commands supported as controller On Commands Supported as responder On Off Fast-on Fast-off Begin bright Begin dim End bright End dim Incremental bright Incremental dim Software Configurable Yes RF Range Up to 50 meters open air Phase detect beacon Yes X10 Support Yes X10 Addresses Any 1 of 256 (unassigned by default) Mechanical Mounting Behind switch or outlet, or above light fixture in a single-gang electrical box Wires Analog + 0-10V Control (Gray wire) Analog - 0-10V Control (purple wire) Line Neutral Load 1 Load 2 Set Button 1 Beeper Yes Beep on button press Optional (off by default) LED 1, green/red Dimensions 171mm (wide), 30mm (high), 35mm (deep)
6.75-in. (wide), 1.2-in. (high), 1.4-in. (deep)
Weight 5.1 ounces Operating Environment Indoors Operating Temperature Range 32° F to 104° F (0° C to 40° C) Operating Humidity Range 0-90% relative humidity, non-condensing Storage conditions -4° F to +158° F (-20° C to 70° C) Case Color White Plastic UV stabilized polycarbonate Electrical Voltage 100-277VAC ± 10% Frequency 50Hz/60Hz Maximum Load 0-10VDC for connection to dimmable ballast
Load 1; 100 to 277VAC / 5Amps
Load 2; 100 to 277VAC / 5Amps
Hardwired remote control RJ-10 Mini-modular jack four conductor Hardwire port wiring
Group 1 - 2
Hardwire port triggering Group 1: triggers when switch between Pin 3 & 4 is closed
Group 2: triggers when switch between Pin 3 & 4 is opened
Group 3: triggers when switch between Pin 2 & 4 is closed
Group 4: triggers when switch between Pin 2 & 4 is opened
Retains all settings without power Yes, saved in non-volatile EEPROM Load Type(s) Wired in ballasted dimming and non-dimming lighting loads Retains all settings without power Yes, saved in Non-volatile EEPROM Standby power consumption < 1 watt Safety Approved ETL Certifications FCC 15.107, 15.109, 15.249
EN 300 220-2, 301 489-3
AS/NZS 4268, CISPR 22
FCC ID SBP2475DA2
- Review of 2475DA2 Review by B.T.
Review of 2475DA2
Been waiting a long time for this one! Works as a standard dimming light device- paired right up with my Vera. Using it to control a Cree CR14 0-10V LED fixture, the dimming control is very precise. I am surprised at how loud the relay is when the light turns off! Make it as quiet as the micro relays, and if it lasts 5 years without failing- it will be a 5 star product.
Posted on 9/19/2013
Leave a Review
- INSTEON 0-10V Ballast Dimmer