DynaQuip Controls ZWCFS100 Z-Wave WaterCop Wireless Water and Freeze Alarm
Share Share Share Share Share
Rewards: 79 Points

DynaQuip Controls ZWCFS100 Z-Wave WaterCop Wireless Water and Freeze Alarm

Send an Alert to Your Z-Wave Network Whenever Water, Freezing Temperatures, or a Low-Battery Condition is Detected
  • Monitors for both leaks and freezing temperatures
  • Emits an 82dB audible alert whenever water is detected
  • Sends Alert across Z-Wave network for water detection, freezing temperatures, and low battery conditions
  • Works with WaterCop Z-Wave Automatic Shut-Off Valve
  • Wireless range up to 100-feet through doors, walls, and floor

Item #: 71627

In stock - Ships Today

Special Price: $79.43

List Price: $93.45

Your Savings: $14.02

  • Details
  • Specs
  • Reviews
  • This Z-Wave enabled Wirelss Water and Freeze Alarm monitors your home 24-hours a day for leaking pipes, corroded water heaters, fixtures in bathrooms and laundry rooms, automatic water and ice dispensers, and other appliances that could cause water damage. Upon the detection of water or freezing temperatures, this device will send out a water leak alert on our Z-Wave network. The ZWCFS100 sensors are much more effective at protecting your home against water damage when used with a WaterCop Z-Wave Automatic Shut-Off Valve (Sold Separately), but not needed. Using the ZWCFS100 that has not been included with a Z-Wave network will still notify you of leaks (audible alarm does not sound for temperature alerts) using the audible alarm. This unit is battery powered and will send an alert throughout the Z-Wave network at regular intervals when a low-battery condition, in addition, an audible "chirp" will sound to alert you of a low battery within the water and freeze alarm.

    Built into this sensor is a 85 decibel siren. This siren will sound an 82 decibel audible alarm and will send an alert message to the Z-Wave network (If already included in a Z-Wave network). Pressing and performing a 2-second hold on the Program switch will clear the Water Alarm. When freezing temperatures are detected an alert message is sent to the Z-Wave network. No audible alert will occur. With a Z-Wave gateway or the appropriate web-enabled Z-Wave controller, you will be able to check the status of this sensor remotely as well as receive text message via smartphone or email messages whenever an alert is sent. Install this sensor under sinks, next to sump pumps, water heaters, laundry rooms, bathroom floor, storage area, garage, utility sink, vacation/recreation homes, boats, etc.

  • Specifications
    ManufacturerDynaQuip Controls
    Manufacturer Product No.ZWCFS100
    PowerOne 3.6V 1/2AA 1200mAh Lithium Battery, ER14250J, LS14250 or equivalent
    Battery LifeCalculated to be 1 to 2 years with no alarms and default Z-Wave network settings
    Frequency Range908.42MHz (US)
    Distance RangeMax 100ft line of sight in unobstructed environment
    Product Size (LxWxD)2.4" x 1.6" x 0.8"
    Product Weight0.2 lb
    Operating Temperature-10° C (14° F) to 70° C (158° F)
    Reported TemperatureReported temperature is at the unit and has a +/- ° accuracy
    System RequirementAny Z-Wave enabled network and controller
  • 1 Review

    Review of 71627 Review by WESLEY
    Review of 71627

    Save your money! First device the alarm did not work. I had to pay for shipping back the defective unit only to receive a second unit that the alarm did not work on. Not wanting to pay for shipping again I tested it on my z-wave network. I set it up to send a text on alarm but it only sent it after I reset the alarm by physically pressing the reset button on the unit!? By that point my basement would be flooded. Absolutely useless product!

    Posted on 1/6/2013

    Leave a Review

    You're reviewing: DynaQuip Controls ZWCFS100 Z-Wave WaterCop Wireless Water and Freeze Alarm

    • 1 star
      2 stars
      3 stars
      4 stars
      5 stars

    * Required Fields

place your order by 3pm PT for same day shipping

Please wait...