1-12 of 32 Results in Best Seller Order
|
Compare up to 10 items now
|
View:
At A Glance
|
Detailed
Products Per Page:
12
|
24
|
48
1
|
2
|
3
|
>
|
|
Sort By:
|
|
|
Intermatic IG1240RC3 Whole House Surge Protector
|
|
The Intermatic IG1240RC3 Whole House Surge Protector features six modes of protection and is recommended for residential and light commercial applications. It is intended for installation on 120/240 volt AC panels.
More info...
|
|
|
Part #
48716
|
Compare
|
|
Sale $112.90
$193.50
|
|
|
HomePro CR234 Amplified X10 Coupler Repeater with Repeated Signal Detection
|
|
For large, complex X10 installations where it may be necessary to use more than one amplifier, this unit can be set to ignore previously amplified and repeated signals and only repeat/amplify original X10 signals.
More info...
|
|
|
Part #
4821AC
|
Compare
|
|
Sale $154.01
$192.50
|
|
|
HomePro CR230 Amplified Coupler-Repeater
|
|
For systems with less demanding needs, this module amplifies X10 signals of 100mV or more to 5V across both phases of a 120/240 VAC split-single phase distribution system commonly found in a single family home.
More info...
|
|
|
Part #
4820AC
|
Compare
|
|
Sale $101.92
$122.50
|
|
|
HomePro CR134 3-Phase Amplified X10 Coupler Repeater w/ Repeated Signal Detection
|
|
For locations where there is three-phase electrical service, this unit can be set to ignore previously amplified and repeated signals and only repeat/amplify original X10 signals.
More info...
|
|
|
Part #
4822AC
|
Compare
|
|
Sale $199.72
$210.00
|
|
|
6db Attenuator Pad (1 each)
|
|
Screw in-line with coax cable and reduce signal strength by rated amount. Try different combinations until you get the best picture quality. Use to balance signal strength from different sources.
More info...
|
|
|
Part #
7802
|
Compare
|
|
Sale $0.96
$1.99
|
|
|
10 dB Attenuator Pad (1 each)
|
|
Screw in-line with coax cable and reduce signal strength by rated amount. Try different combinations until you get the best picture quality. Use to balance signal strength from different sources.
More info...
|
|
|
Part #
7803
|
Compare
|
|
Sale $1.11
$1.99
|
|
|
ACT AT004 X10 Multi-Tester Transceiver
|
|
Optimally set up your X10 devices by thoroughly testing signal strengths to make sure the system is functioning to capacity.
More info...
|
|
|
Part #
2200ATT
|
Compare
|
|
Sale $220.03
$270.00
|
|
|
3db Attenuator Pad (1 each)
|
|
Screw in-line with coax cable and reduce signal strength by rated amount. Try different combinations until you get the best picture quality. Use to balance signal strength from different sources.
More info...
|
|
|
Part #
7801
|
Compare
|
|
Sale $1.11
$1.99
|
|
|
Attenuator Pad Mix Bag (2 Ea. 3, 6,10 & 20 Db Pads)
|
|
Install in-line with coax cable and reduce signal strength by rated amount. Try different combinations until you get the best picture quality. Use to balance signal strength from different sources.
More info...
|
|
|
Part #
7800
|
Compare
|
|
Sale $6.99
$15.92
|
|
|
Channel Plus LPF-750 Low Pass Filter, Passes CATV 2-116, Blocks CATV >121
|
|
Must use for creating a clean channel range for inserting your own signals. Prevents cable company signals on unused channels from interfering with your modulated channels .
More info...
|
|
|
Part #
7822D
|
Compare
|
|
Sale $35.59
$54.60
|
|
|
Wire-In UPB Phase Coupler-Breaker Panel
|
|
Connect this universal phase coupler in your home's circuit breaker box, and it will bridge UPB as well as X10 signals between the two power lines in your home easily, allowing virtually all of your automation receivers to respond reliably to remote commands.
More info...
|
|
|
Part #
22934B
|
Compare
|
|
Sale $55.83
$69.99
|
|
|
HomePro CP000 X10 Signal Bridge
|
|
If X10 transmitters in one part of your home seem to be unable to control X10 devices in another part of your home, this signal bridge will most likely solve the problem.
More info...
|
|
|
Part #
4815AC
|
Compare
|
|
Sale $9.30
$12.25
|
|
|
|
1-12 of 32 Results in Best Seller Order
|
1
|
2
|
3
|
>
|
|