1-12 of 31 Results in Best Seller Order
|
Compare up to 10 items now
|
View:
At A Glance
|
Detailed
Products Per Page:
12
|
24
|
48
1
|
2
|
3
|
>
|
|
Sort By:
|
|
|
SignaLinc Plug-In Phase Coupler (For 3-Wire 220v Dryers)
|
|
Increase X10 signal reliability simply by plugging in this phase coupler. No hardwiring required!
More info...
|
|
|
Part #
4816B2
|
Compare
|
|
Sale $29.99
$39.99
|
|
|
Leviton 6287 Noise Block
|
|
High Pressure Discharge lighting (HID) including Mercury, Sodium Vapor and Metal Halide types often generate a significant amount of noise when turned off. The noise usually turns the X10 fixture module back on immediately after it is turned off. This noise block will filter out that noise.
More info...
|
|
|
Part #
4835
|
Compare
|
|
Sale $25.61
$37.99
|
|
|
X10 PZZ01 Pro Whole-House X10 Blocking Coupler
|
|
Slip this whole-house blocking coupler over the neutral wire feed entering the house. It senses the presence of electrical noise and X10 signals, then it generates an offsetting voltage signal to attenuate the entering noise and X10 signals.
More info...
|
|
|
Part #
4851X
|
Compare
|
|
Sale $52.99
$59.99
|
|
|
X10 XPCP X10 Passive Signal Coupler
|
|
If X10 transmitters in one part of your home seem to be unable to control X10 devices in another part of your home, this signal bridge will most likely solve the problem.
More info...
|
|
|
Part #
4815X
|
Compare
|
|
Sale $41.99
$46.99
|
|
|
Attenuator Pad Mix Bag (2 Ea. 3, 6,10 & 20 Db Pads)
|
|
Install in-line with coax cable and reduce signal strength by rated amount. Try different combinations until you get the best picture quality. Use to balance signal strength from different sources.
More info...
|
|
|
Part #
7800
|
Compare
|
|
Sale $6.99
$15.92
|
|
|
Leviton 6289 In-Line Noise Reducer
|
|
A filter that can be used with any load or installed near an X10 module that is being affected by powerline interference. Filters out electrical noise above and below the 121Khz X10 signal but allows the X10 signal to pass through.
More info...
|
|
|
Part #
4840
|
Compare
|
|
Sale $39.75
$56.99
|
|
|
|
HomePro CP000 X10 Signal Bridge
|
|
If X10 transmitters in one part of your home seem to be unable to control X10 devices in another part of your home, this signal bridge will most likely solve the problem.
More info...
|
|
|
Part #
4815AC
|
Compare
|
|
Sale $10.42
$12.25
|
|
|
Wire-In UPB Phase Coupler-Breaker Panel
|
|
Connect this universal phase coupler in your home's circuit breaker box, and it will bridge UPB as well as X10 signals between the two power lines in your home easily, allowing virtually all of your automation receivers to respond reliably to remote commands.
More info...
|
|
|
Part #
22934B
|
Compare
|
|
Sale $53.82
$69.99
|
|
|
4 Conductor Wall Nuts, 100 Pack
|
|
Safe for use with 18- to 12-gauge solid wire or 16- to 12-gauge stranded wire, these 100 wire connectors will hold wires securely so they can't pull out accidentally.
More info...
|
|
|
Part #
7877P
|
Compare
|
|
Sale $7.72
$13.99
|
|
|
|
Leviton 6299 X10 Signal Bridge
|
|
If X10 transmitters in one part of your home seem to be unable to control X10 devices in another part of your home, this signal bridge will most likely solve the problem.
More info...
|
|
|
Part #
4815
|
Compare
|
|
Sale $39.47
$44.99
|
|
|
Channel Plus NF-471 Notch Filter, Blocks CATV 75-80
|
|
Block CATV channels 75-80 and off-air UHF TV channels 24-29 to allow modulators to insert a channel without interference.
More info...
|
|
|
Part #
7822G
|
Compare
|
|
Sale $25.49
$45.30
|
|
|
10 dB Attenuator Pad (1 each)
|
|
Screw in-line with coax cable and reduce signal strength by rated amount. Try different combinations until you get the best picture quality. Use to balance signal strength from different sources.
More info...
|
|
|
Part #
7803
|
Compare
|
|
Sale $1.11
$1.99
|
|
|
|
1-12 of 31 Results in Best Seller Order
|
1
|
2
|
3
|
>
|
|