• Comes with everything needed to assemble the wind turbine
• Produces up to 800W of power in 29mph wind
• Produces up to 1100W of power in 35mph wind
• Works with both 12 Volt and 24 Volt battery banks
• Furling allows turbine to withstand high wind speeds

The WGN-CWTK-75 WindTura 750 Complete Wind Turbine Kit from Windy Nation allows its user to capture the kinetic energy of the wind to generate electricity. The WindTura 750 is capable of producing 800 Watts of power in 29mph wind speeds and as much as 1100 Watts of power in 35mph wind speeds. This generated electricity can be used for applications such as to feed a grid tie inverter, off grid power or to charge 12 Volt or 24 Volt battery banks. The electricity is captured by three, 35 inch blades which use the kinetic energy of the wind to rotate its 3 phase AC permanent magnet alternator. Electrical power is produced by the rotation of the permanent magnet alternator and is then transferred by 3 electrical wires to ground level.

To protect itself from damage and failure in high wind conditions the WindTura 750 uses a method referred to as furling. The assembled tail is attached to the yaw mount which is on a 20 degree angled pivot bar. This pivot bar is what allows the yaw mount and generator to rotate away from the wind as speeds gust over 30mph. Once wind speeds exceed roughly 30mph the generator and blades will begin to rotate out of the wind as a result of the rotational inertia of the spinning blades. As wind speed continues to increase the generator and blades will continue to rotate out of the wind until they reach nearly 90 degrees to ensure they are protected. When the wind speed returns to a speed of 30mph or lower the generator and blades will begin to unfurl and face the wind directly again to ensure optimum performance. Without this rotation away from the wind the turbines generator would begin rotating at such high rpms that the current (amps) produced would be too much heat for the generator to handle causing it to overheat and breakdown. To ensure that the furling mechanism works correctly it is important to make sure the tower is installed vertically and it is recommended that a level be used to confirm this. If the WindTura is not mounted vertically then the generator and blades can begin to furl at undesignated wind speeds. For optimum performance it is recommended that the turbine be mounted 20 feet above all nearby objects.

Please Note:Your Windy Nation WindTura 750 Wind Turbine is designed with your personal safety as the first priority. However, there are still some inherent dangers involved with any electrical and/or mechanical equipment. Safety must be the primary concern as you plan the location, installation and operation of the turbine.

• Smarthome does not offer technical support on this product, please contact the manufacturer directly for all product support.
• Only defective exchanges for identical item within 30 days of purchase. No other returns allowed on this item. For defective returns after 30 days, please contact the manufacturer.

• Owner's Manual

1x - Generator / Yaw Mount

1x - Permanent Magnet Alternator or PMA (pre-attached to generator/yaw mount)

1x - 3 phase slip ring + strain relief (pre-attached to generator/yaw mount)

1x - Yaw bushing

1x - Tail boom

1x - Tail mounting bracket

1x - Directional Tail

3x - 35 inch WindGrabber Blades

1x - Stainless steel 3-blade hub

1x - All necessary bolts, nuts and washers to make connections to assemble

1x - Owner's manual

Sunforce Products 600 Watt Land Wind Turbine Power Generator with MPPT Charge Controller	Sunforce Products 37130 130 Watt Polycrystalline Solar Panel	Sunforce Products 60 Watt Monocrystalline Solar Panel with 7 Amp Charge Controller	Powerhouse Dynamics eMonitor4-44 Intelligent Residential Power Usage Monitor
Universal Power Group Ecotricity Solar Generator	Natural Light Energy Systems 30 Watt Roof Mounted Attic Fan	US Sunlight Corp 9910TRP 1,350sq/ft Ventilating Solar Attic Fan	StoreBound LP001SIL The Laundry POD - Platinum