|
|
| Intermatic Hardwired Protector - 4 Telephone - 2 Coaxial |
|
|
| Item# 4872 |
|
|
|
|
|
Overview
|
- Protects electrical, phone, and coax lines
- Wires into main breaker box
- Safe for indoor or outdoor use
Essential Info
Surge protectors will defend electrical devices from damage in the event of transient surges, but your electrical devices aren't your only possessions in danger. By installing the Intermatic Hardwired Protector in your home's indoor or outdoor breaker panel, you'll be protecting your AC power as well as up to four telephone lines and two coax lines from the surges that can destroy their connected components. The Intermatic Hardwired Protector even carries a 5-year warranty with a $10,000 connected-equipment warranty.
Manuals/Software
What's Included
Panel guard with 30" wire leads
Mounting plate
Wire channel cover
2 four-wire (2-pair) telephone protection modules
2 1-circuit coaxial cable protection modules
|
More Info
|
Designed for 120/240 VAC single (split) phase homes, the Intermatic Hardwired Protector installs into a 15- or 20-ampere breaker. This single device will protect AC power, four phone, modem or high-speed data lines, and two coax connections, ideal for homes with both cable and satellite feeds.
The "All Mode" protection configuration provides distinct protection paths between every conductor in the AC electrical system. When installed on service entrance or main panels with a common neutral-ground bus, line-to-neutral and line-to-ground protective circuits are paralleled for redundancy and maximum current capability. On subpanels with separate neutral and ground buses, protection is provided against all possible modes of surge energy with distinct line-to-neutral, line-to-ground, neutral-to-ground and line-to-line protection components.
The Intermatic Hardwired Protector is shipped ready for installation on the right-hand side or top positions of the electrical panel, but it can be mounted on the left a few minor adjustments. Dedicated circuits monitor each component in each mode and control the operation of each phase LED indicator. Lighted green indicators represent normal power-on and unit operational condition. A red indicator will light up if protection is reduced or lost.
This Intermatic Hardwired Protector will protect four telephone lines and two coax line. If you don't need this many lines protected, try the two telephone lines and one coax line protector instead.
|
Specifications
|
Specifications | | Manufacturer: | Intermatic | | Manufacturer Product No.: | IG1300-4T-2C | | UPC: | 078275084872 | | Dimensions: | 10" x 6" x 4" | | Weight: | 2.85 pounds | | Wire Sizes: | 26 through 18 gauge | | AC Voltage Configuration: | 120 / 240 VAC single phase (split phase) | | Maximum Continuous Operating AC Voltage: | 115% | | Operating Frequencies: | 50, 60, 400 Hz | | Actual Suppressed AC Voltage: | (6 kV @ 500 amps) line to neutral: 354; line to ground: 352; neutral to ground: 340; line to line: 649 | | UL1449 Suppressed AC Voltage - SVR: | (6 kV @ 500 amps) line to neutral: 400; line to ground: 400; neutral to ground: 400; line to line: 700 | | Surge Current Ratings (8 x 20 µSec.): | Per phase (L - N + L - G): 20,000 amps; total system: 60,000 amps | | UL Fault Current Rating: | 25,000 amps | | Operating Temperature: | -40° F to 185° F (-40° C to 85° C) | | Approvals: | UL listed | | Warranty: | 5 years, plus $10,000 connected equipment, limited |
Telephone/Data Line Protection | | Protection Modes: | Common mode: tip to ground, ring to ground; transverse mode: tip to ring | | Longitudinal Balance: | (TIA -IS-968) Off-hook from 200 Hz to 4kHz: > 40 dB; on-hook from 200 Hz to 1 kHz: > 60 dB; on-hook from 1 kHz to 4 kHz: > 40 dB | | Voltage Compatibility: | (TIA -IS-968) Ring voltage of 40 - 150 VAC - 15 to 68 Hz: functional pass | | Gas Tube Rating: | 350 VDC |
Coaxial Line Protection | | Protection Mode: | Common mode: signal to ground | | Electrical Impedance: | 75 ohms @ 20 - 100 MHz: (± 0.5 ohms) | | Insertion Loss: | 20 MHz - 300 MHz: < 0.1 dB; 300 MHz - 500 MHz: < 0.5 dB; 500 MHz - 1 GHz: < 1.8 dB | | Voltage Compatibility: | 0 - 48 VDC functional pass | | Gas Tube Rating: | 90 VDC |
|
Images/Video
|
|
|
Reviews
|
|
|
Related Items
|
Customers Also Bought
|
|
|
|