|
|
| Venstar Remote Duct Digital Temperature Sensor Wire |
| Item# 30409 |
|
|
|
|
|
|
Overview
|
- Digital remote temperature sensor can be used with compatible Venstar thermostats
- Temperature detection range of -40° F to 127° F
- Can be used as a duct sensor or as and indoor temperature sensor
Essential Info
The Venstar Remote Duct Digital Temperature Sensor measures indoor air temperature in the return air duct with a range of -40° F to 127° F. If used indoors as a remote digital temperature sensor, the sensor will read room temperature and send the information to the thermostat. If used as a duct temperature sensor, this sensor may be used to provide duct temperature information (which is not used to control heating or cooling). It is constructed with plenum-rated cable and a rubber grommet is included to protect the cable from the edge of sheet metal. This sensor may also be used as a remote room temperature sensor where an unobtrusive sensor is required. When used as remote room sensor, the accessory can be used with Venstar 7-day Programmable Digital Thermostat, 7-Day Programmable Thermostat, Dual Fuel and model T2700, T2900, T2900SCH and T2300FS thermostats, each sold separately. The wire senses room temperature where it is installed and should be connected to the thermostat using solid conductor CAT 5, CAT 5e, or CAT 6 type network communication cable (The cable length should not exceed 250 feet) The thermostat will show a blinking degree icon next to the temperature display and can then be programmed based on the sensor readings.
Manuals/Software
What's Included
Venstar Remote Duct Temperature Sensor
Wire nuts
Grommet
Owner's manual
|
More Info
|
Correct Application
When used as a duct sensor, this sensor should be mounted in the return air duct. When used as a remote temperature sensor, the Duct Sensor should be mounted in an indoor location approximately five feet from the floor, close to or in a frequently used room, preferably on an inside partitioning wall or on a section of wall without pipes or ductwork. Mount the sensor where temperature operating limits are within 32° to 99° F and the humidity operating range is within 0% to 95% relative humidity, non-condensing.
Incorrect Applications
The Duct Sensor should NOT be mounted close to a window, on an outside wall, or next to a door leading to the outside. Do not mount the sensor in a location where it would be exposed to direct light and heat from a lamp, the sun, a fireplace, or any other temperature-radiating object which may cause a false reading. Finally, do not mount the sensor close to or in direct airflow from supply registers or return air grilles and in areas with poor air circulation (such as behind a door or in an alcove).
Wiring Requirements
The Duct Sensor should be connected to the thermostat using solid conductor CAT 5, CAT 5e, or CAT 6 type network communication cable. This is an unshielded cable with four twisted pairs of 24 gauge solid wire; DO NOT use stranded cable. The cable length should not exceed 250 feet. If less than 75 feet of cable is required to connect the thermostat to the Duct Sensor, a three conductor thermostat cable (18-24 gauge) may be used; this cable is NOT suitable for any length greater than 75 feet.
IMPORTANT: Do no use shielded wire. Do not run sensor wiring in the same conduit as the 24VAC thermostat wiring. Electrical interference may cause the sensor to give incorrect temperature readings.
|
Specifications
|
Specifications | | Manufacturer: | Venstar | | Manufacturer Product No.: | ACC0435 | | Operating Temperature: | 32° F to 99° F | | Operating Humidity: | 0% to 95% | | Temperature Detection Range: | -40° F to 127° F | | Compatability: | Venstar 7-day Programmable Digital Thermostat, 7-Day Programmable Thermostat, Dual Fuel and model T2700, T2900, T2900SCH and T2300FS thermostats | | Connection Cable: | Solid conductor CAT 5, CAT 5e, or CAT 6 type network communication cable |
|
Images/Video
|
|
|
Reviews
|
|
|
Accessories
|
|
|
Related Items
|
Customers Also Bought
|
|
|