| General |
| Brand: | INSTEON |
| Manufacturer product no.: | 2477S - SwitchLinc On/Off - INSTEON Remote Control On/Off Switch (Dual-Band) |
| UPC: | White - 2477S: 813922012378
Almond - 2477SAL: 813922013245
Light Almond - 2477SLAL: 813922013290
Black - 2477SBK: 813922013252
Gray - 2477SGY: 813922013276
Ivory - 2477SIV: 813922013283
Brown - 2477SBR: 813922013269 |
| FCC ID: | SBP2477S |
| Patent no.: | U.S. Patent No. 7,345,998. Protected under U.S. and foreign patents (see www.insteon.com). |
| Warranty: | 2 years, limited |
| Operation |
| LED indicator: | 8 white LEDs. Optional green, blue, amber or red LEDs with #2400L kit. |
| Operation modes: | INSTEON only, X10 only, INSTEON and X10 combo mode |
| Combo mode message order: | INSTEON, INSTEON cleanup, X10 |
| Multi-way circuit support: | One SwitchLinc Relay controls load, cross-link any number of SwitchLincs or other INSTEON Controllers |
| Setup memory: | Non-volatile EEPROM |
| INSTEON Features |
| INSTEON addresses: | 1 |
| INSTEON | 400 responder groups and 1 controller group |
| Maximum scene memberships | 400 (combined controller + responder) |
| Scene commands supported as controller | On | Off |
| Fast-on | Fast-off |
| Begin brighten | End brighten |
| Begin dim | End dim |
| Scene commands supported as responder | On | Off |
| Fast-on | Fast-off |
| Software configurable | Yes |
| INSTEON powerline frequency: | 131.65 KHz |
| INSTEON minimum transmit level: | 3.2 Vpp into 5 Ohms |
| INSTEON minimum receive level: | 10 mV |
| INSTEON messages repeated: | Yes |
| Radio frequency: | 915 MHz |
| RF Range | >100' (open air) |
| Mechanical |
| Paddle Type: | True rocker action |
| Wire Nuts: | 4 included |
| Wires | Line (Hot) - black, 12 AWG |
| Neutral - white, 18 AWG |
| Load - red, 12 AWG |
| Ground - bare copper, 12 AWG |
| Mounting: | Standard, single-gang wall box |
| Color: | White (color change kits available) |
| Set button: | Clear |
| Air gap: | Set button when pulled out |
| Plastic: | UV stabilized polycarbonate |
| Beeper: | Yes |
| Setup LED: | 1 red/green dual-color |
| Status LEDs: | 2 white, can be dimmed or disabled (color change kits available) |
| Operating conditions: | Indoors, 32-104°F, up to 85% relative humidity |
| Dimensions: | 4.1" H x 1.78" W x 1.47" D |
| Weight: | 4.2 oz |
| Electrical |
| Supply voltage: | 100-277VAC +/- 10%, 50/60Hz auto-detected at power-up |
| Neutral wire: | Required |
| Power wire leads: | 6", 12 AWG, stranded, 600V, 105°C insulation, ends stripped and tinned, Line (black), Load (red), 18 AWG Neutral (white) |
| Maximum load: | 17 Amp resistive capacity (100-277 VAC) |
| 1,800 Watt incandescent capacity (100-277 VAC) |
| 1 HP motors (at 120 VAC only) |
| 10 Amps ballast |
| Surge resistance: | Up to 500 VAC |
| Retains all settings without power: | Yes, saved in non-volatile EEPROM |
| Standby power consumption: | <1 Watt |
| Safety approved: | ETL (Intertek Testing Services) |
| Certification: | Safety tested for use in USA and Canada |
| X10 Features (applies to powerline only) |
| X10 primary address: | 1 optional (comes unassigned) |
| X10 scene address: | 256 maximum (unassigned by default) |
| X10 status response: | Supported |
| X10 powerline frequency: | 120 KHz |
| X10 minimum transmit level: | 3.2 Vpp into 5 Ohms |
| X10 minimum receive level: | 20mV into 5 Ohms |
| X10 messages repeated: | No |