|
Find Similar Products in:
|
|
|
| 2-Wire INSTEON Dimmer Kit, White |
|
|
| Item# 2474D |
|
|
|
|
|
Overview
|
- Allows you to remotely control lights where a neutral wire is not present in the switch box
- Save money on bills by dimming your lights with this 300-watt dimmer
- Convenient: Once installed, companion switch and fixture module operate as one device from the switch
- Uses existing wires to provide a neutral to your companion switch for added reliability
- Award-winning INSTEON technology provides superior performance and reliability
Essential Info
Can't use INSTEON because you don't have neutral wires in your switch boxes? You can now, with our new INSTEON 2-wire Dimmer Kit. Remotely control and dim your lights, even if you don't have those once-needed neutral wires in your switch boxes. Now you can enjoy the speed and reliability of INSTEON where never-before possible. Don't have a neutral somewhere you'd like to control ANY load type? An INSTEON 2-wire On/Off Kit is also available. Do I have neutrals? How it WorksThe INSTEON 2-wire Dimmer Kit comes with two main pieces: a companion switch that installs in the switch box and a fixture dimmer that installs in your light fixture. With these two devices you'll now be able to convert one of your two wires in your switch box to a neutral, enabling reliable control of your light. The companion switch and fixture dimmer are "paired" at the factory so both devices will act as one. This means that once they're installed, you won't have to go back into the fixture, either for control OR for linking to other INSTEON-compatible devices. Simply put, the companion switch's SET button acts as a remote SET button for the fixture dimmer, giving you added convenience and flexibility. View our Videos:Smarthome Home Tour
Would you like to try INSTEON before you buy? Check out our Flash Demo to take a test drive!
Manuals/Software
What's Included
Companion Switch
Fixture Dimmer - 300 watt
Quick-Start Guide
4 mounting screws
6 wire nuts
|
More Info
|
Scene Lighting
Scenes allow you to control multiple lights, rooms or even the whole home with a single command. Because the 2-wire kit can be a member of more than 400 scenes (i.e. "Movie Time," "Party," "Romance," etc.), you'll be able to launch various lighting scenarios with a single button press. These are elegant features usually found only in systems costing tens of thousands of dollars and requiring extensive rewiring of your home. All member lights can ramp to your independently desired brightness levels at your chosen ramp rate(s). So one set of lights can dim slowly, while another set turns off instantly, all controlled with one command from one button. If you want to control multiple scenes from one controller, upgrade to the INSTEON KeypadLinc Dimmer.
X10 Compatible
The INSTEON 2-wire Kit is fully INSTEON compatible and X10 ready. Homeowners with existing X10 networks can easily migrate to an INSTEON network without having to discard all their existing X10 devices. X10 ready means that it can respond to X10 commands from an X10 controller and it can send X10 commands to X10 devices. Please note that INSTEON devices repeat INSTEON signals but not X10.
Non-Volatile Memory
All 2-wire kit settings are stored in non-volatile memory and are not lost during power failures. Additionally, in the event of a power loss, the 2-wire Dimmer Kit will return to its last brightness level when power is restored.
Certifications and Warranty
All SmartLabs Design products are safety approved. The factory for SmartLabs Design products is ISO9001 certified. Because of this passion for quality, Smarthome stands behind the entire line of products with a full 2-year warranty.
|
Specifications
|
Fixture Dimmer Specifications | | General | | Brand: | Smarthome | | Manufacturer: | SmartLabs Design | | Manufacturer Product No.: | 2474D, INSTEON 2-Wire Dimmer Kit | | UPC: | 689076408745 | | Multi-Way Circuit Support: | Yes, as a receiver only that controls a load | | Warranty: | 2 years, limited | | Patent No.: | U.S. Patent No. 7,345,998, International patents pending | | Operation | | On-Levels | 32 locally, increments of 1% with software | | Ramp Rates (full-ON to full-OFF) | 0.1 to 9 seconds if programmed locally, 0.1 seconds to 9 minutes if programmed remotely | | LED Indicator: | Off when load is on and vice versa | | Operation Modes | INSTEON only, X10 only, INSTEON and X10 Combo Mode | | Combo Mode Message Order | INSTEON, X10, INSTEON cleanup | | Setup Memory | Non-volatile EEPROM | | INSTEON Features | | INSTEON Addresses | 1 hard-coded out of 16,777,216 possible | | INSTEON Links | 417 | | INSTEON Powerline Frequency | 131.65 KHz | | INSTEON Minimum Transmit Level | 3.2 Vpp into 5 Ohms | | INSTEON Minimum Receive Level | 10 mV | | INSTEON Messages Repeated | Yes | | Mechanical | | Wire Nuts | 3 included | | Mounting | Mounts in single-ganged junction box or light fixture such as a recessed can light. | | Operating Conditions | Indoors, 0 to 104°F, up to 85% relative humidity | | Dimensions | 3.75" H x 1.8" W x 1.2" D (2.75" H without screw tabs) | | Weight | 3.6 oz | | Electrical | | Supply Voltage | 120 Volts AC +/- 10%, 60 Hertz, single phase | | Surge Protection | MOV rated for 150 Volts | | Power Wire Leads | 6", 16 AWG, stranded,600V, 105°C insulation, ends stripped and tinned, LINE (black), LOAD (red), NEUTRAL (white) | | Ground Lead | 6", 18 AWG, stranded, bare copper | | Load Types | Wired-in incandescent lighting devices | | Maximum Load | 300 Watts | | Minimum Load | No minimum load required |
| Certification | Safety tested for use in USA and Canada (ETL) | | X10 Features | | X10 Primary Address | 1 optional (comes unassigned) | | X10 Scene Addresses | 255 possible | | X10 Status Response | Supported | | X10 Resume Dim | Supported (by setting Local On-Level to zero) | | X10 Powerline Frequency | 120 KHz | | X10 Minimum Transmit Level | 3.2 Vpp into 5 Ohms | | X10 Minimum Receive Level | 10 mVpp nominal | | X10 Messages Repeated | No |
Companion Switch Specifications | | Operation | | Warranty: | 2 years, limited | | LED Indicator | One Amber LED | | Operation Modes | INSTEON only, X10 only, INSTEON and X10 Combo Mode | | Combo Mode Message Order | INSTEON, X10, INSTEON cleanup | | Setup Memory | Non-volatile EEPROM | | INSTEON Features | | INSTEON Addresses | 1 hard-coded out of 16,777,216 possible | | INSTEON Links | 30 | | INSTEON Powerline Frequency | 131.65 KHz | | INSTEON Minimum Transmit Level | 3.2 Vpp into 5 Ohms | | INSTEON Minimum Receive Level | 10 mV | | INSTEON Messages Repeated | Yes | | Mechanical | | Paddle Type | True rocker action | | Color | White installed, Optional Ivory, Almond, Black, Brown, or Grey | | Wire Nuts | 3 included | | Mounting | Mounts in single or multiple-ganged junction box. | | Operating Conditions | Indoors, 40 to 104°F, up to 85% relative humidity | | Dimensions | 4.1" H x 1.8" W x 1.2" D | | Weight | 3.6 oz | | Electrical | l| Supply Voltage | 120 Volts AC +/- 10%, 60 Hertz, single phase | | Surge Protection | MOV rated for 150 Volts | | Power Wire Leads | 6", 16 AWG, stranded, 600V, 105°C insulation, ends stripped and tinned, LINE (black), NEUTRAL (white) | | Ground Lead | 6", 18 AWG, stranded, bare copper | | Certification | Safety tested for use in USA and Canada (ETL #3017581) | | X10 Features | | X10 Primary Address | 1 optional (comes unassigned) | | X10 Scene Addresses | N/A | | X10 Status Response | Supported | | X10 Resume Dim | Supported (by setting Local On-Level to zero) | | X10 Powerline Frequency | 120 KHz | | X10 Minimum Transmit Level | 3.2 Vpp into 5 Ohms | | X10 Minimum Receive Level | 10 mVpp nominal | | X10 Messages Repeated | No |
|
Images/Video
|
|
|
Reviews
|
|
|
Accessories
|
|
|
Related Items
|
Customers Also Bought
|
|
|
|
|
|