|
|
| Advector inVent-M/R-R1 inVENT Manually Adjustable Register for Remodeling |
|
Item# 23301
|
1 customer rating
|
|
|
|
Free shipping on orders over $50 - See Details
|
|
Overview
|
- Adjust the air flow to lower HVAC system run time, reducing your monthly energy bill
- Replaces old vents and performs better, looks better, and adds value to your home
- Typical installation takes less than thirty minutes and with little more than a screwdriver
- 360° airflow pattern means no more direct drafts from your HVAC vents
- Specially engineered design and material selection help reduce the sound from the duct system and the air noise exiting the vent
Essential Info
We all struggle with those rooms that never get the right amount of air and end up feeling much too cold or way too hot.. But if you are not ready for a fully automated HVAC system...then the Advector inVent-M/R-R1 inVENT Manually Adjustable Register for Remodeling might be just what you need. The unit works by replacing an existing supply register and enables homeowners to manually adjust the amount of airflow coming through the duct system and into the room. By restricting the amount of air that goes into unused or over conditioned rooms, users re-direct conditioned air into rooms that are used and or under conditioned. As a result, in the properly installed system, HVAC unit can run shorter cycles that translate into energy savings and greater comfort. The inVENT register also provides enhanced airflow distribution that results in a better mixing of the conditioned air with the existing room air, all while reducing the noise and direct drafts when compared to traditional metal registers. The manually adjustable inVENT gives you the ability to regulate temperatures by controlling the amount of air that enters each room. This product is also available for new construction, sold separately. Additional FeaturesQuickly make adjustments to room temperatures to address changes in the weather or room occupancy.
The aerodynamic design causes the air to grip the ceiling, wall, or floor to maximize air distribution and comfort
Lower your energy usage without having to spend a fortune
Manuals/Software
What's Included
1x - Advector inVent-M/R-R1 inVENT Manually Adjustable Register for Remodeling
3x - #10 mounting screws
1x - Gasket
1x - Twist Ring
1x - Owner's Manual
|
More Info
|
| Performance Data | | Closing Plate Position | CFM Flow Rate --> | 50 | 100 | 150 | 200 | 250 | 300 | 350 | | Fully Open | Static Duct Pressure --> | 0.05 | 0.09 | 0.14 | 0.22 | 0.34 | 0.57 | 0.73 | | Fully Open | Duct Diameter --> | 8-inch | 8-inch | 8-inch | 9-inch | 9-inch | 9-inch | 9-inch | | Fully Open | Noise Criteria --> | - | 19 | 27 | 34 | 42 | 50 | 62 | | Fully Open | Horizontal Face Velocity --> | 620 | 1180 | 1520 | 1900 | 2320 | 2733 | 3125 | | Fully Open | Horizontal Throw --> | 7 | 16 | 22 | 32 | 41 | 51 | 58 |
Performance Notes
Airflow is in cubic feet per minute.
All pressure is measured in inches of water
Duct Static Pressure is based on 8inch and 9inch duct sizes as indicated
Face Velocity is in feet per minute
Horizontal Throw is calculated based on 50fpm air velocity and 360 degree distribution pattern
inVent cfm rate can be fully controlled by closing and opening of the Closing Plate
The Noise Criteria values are based on a room absorption rate of -10 db, referenced to 1pW and one inVENT
|
Specifications
|
| Specifications | | Manufacturer | Advector | | Manufacturer Product No. | inVent-M/R-R1 | | UPC | 857309003016 | | Base Diameter | 10.4in | | Profile height at full open | 1.7in | | Profile height at full close | 1.0in | | Weight | 1.1lbs | | Primary Material | ABS Plastic | | Surface Finish | White, textured |
|
|
|
Important notes:
Smarthome does not accept any returns for this product. If defective, you will need to contact the manufacturer directly for all warranty issues.
Manufacturer contact information: Advector Systems LLC, Tel: (817) 416-4880
|
Reviews
|
|
|
Related Items
|
Customers Also Bought
|
|
|
|
|