Add $175.00 for FREE shipping
Dim a Set of Lights with an A10 Command
ACT RD134I Wall Mount A10 Dimmer - Ivory
ACT RD134I Wall Mount A10 Dimmer - Ivory
(Pictured in White)
ACT RD134I Wall Mount A10 Dimmer - Ivory
Item# 22016IV
Free shipping on orders over $175 - See Details


  • A10 Technology
  • Supports two way communication
  • Supports and Remembers Scenes
  • Supports Standard Code On, Off, Bright, Dim commands
  • Supports Immediate On commands, multiple dim rate operation, multiple dim rate local control
  • Remembers dim/bright state
  • Soft Start
  • Configurable to disable Soft Start
  • Configurable to support All Lights On, All Lights Off, All Units Off commands
  • Configurable to respond to Status On, Status Off commands as On, Off commands
  • Reversible LED indication
  • 50/60 Hertz operation

Essential Info

The ACT RD134I Wall Mount A10 Dimmer is an A10 enhanced powerline carrier dimming receiver. The RD134 responds to ON, OFF, BRIGHT, DIM, and can be configured to respond to ALL LIGHTS ON, ALL LIGHTS OFF, ALL UNITS OFF, and STATUS REQUEST. Dimmer remembers last dim level for correct status report and restoration of dim level upon power up. Dimmer can also be configured to respond immediately to ALL LIGHTS ON and ALL UNITS OFF. The RD134 is programmable to any of the 256 addresses, and for up to 64 relative scenes and 4 global scenes. The fade rate of the dimmer can be programmed from immediate to 271 seconds over the entire dimming range, with 3.12 seconds being the default setting.


What's Included

  • 1x - Wall Mount A10 Dimmer - Ivory

  • More Info

    These switches work with the commonly-used X10/PLC signals, as well as the proprietary A10 protocol. This makes them ideal for remote or timed control with any X10 transmitter, intelligent controller or X10-based home automation software. Switches respond to "All Lights On," "All Units On," "All Lights Off" and "All Units Off." They're even capable of two-way powerline communication, including the ability to report status upon a status request from an intelligent controller.

    Capable of a Virtual 3-Way Switch
    Because these switches can be controlled from another location from another switch with the same address, they're ideal for creating a virtual 3-way switch. It's ideal for anyone that wants to control a set of lights from more than one location, without having to hire an electrician to run an additional wire between the two switches. Each switch's address can be set via easy, push-button configuring.

    Status LED
    A status LED verifies power to the unit and indicates status and power. The LED can be set to be "ON" (direct acting) or "OFF" (reverse acting) when load is off.

    Note: Because these switches respond to ALL LIGHTS ON, use care when controlling non-lamp loads. Use an X10 appliance module or wall receptacle if you don't want your device to respond to that command.


    • Electrical Requirements
      • Power
        • Supply Voltage: 120 VAC, +/-10%
        • Frequency: 50 or 60 Hz
      • Signal
        • Signal Input: 120 KHz, X10 Powerline Carrier, sensitive to 25 millivolts peak to peak
        • Signal Output: (Status) 120 KHz, X10 Powerline Carrier, minimum 6V peak to peak @ 5 ohm
      • Controlled Output
        • Internal triac: Enclosed, flying lead connections
        • Maximum switching power: 300 watts, 200 watts with break-off side tabs removed
        • Fuses: One (1) .5 amp slo blow on control circuit, factory replaceable only
        • Disconnect: Load Disconnect or Air Gap Switch on face disconnects load for service
    • Mechanical Requirements
      • Dimensions: 2.7" L x 1.75" W x 1.6" H
      • Weight: Less than 16 ounces
      • Mounting: Mounting plate for standard electrical switch box
      • Connections: Flying Leads: BLACK (Line) -16 AWG, BLUE (Load) -16 AWG, WHITE (Neutral) -18 AWG, GREEN (Ground) - 18 AWG.
    • Environmental Requirements
      • Operating Temperature 32 to 120 degrees F
      • Operating Humidity 10% to 95% non-condensing
    Important notes:
    Only merchandise credit for defective items returned within 30 days of purchase. No other returns allowed on this item.
    Manufacturer contact information: Advanced Control Technology Inc, Tel: (317) 337-0100 Ext 236


    Related Items

    Sign-up for Exclusive Email offers 
    How to Order Track Your Package Shipping Returns Contact Us Customer Service Retail Store
    Getting Started Learning Center FAQ Dealers Customer Testimonials Affiliate Program
    About Us INSTEON Press Awards Employment Guarantees Security & Privacy
    Free Catalog Email Newsletter Forum RSS Site Map
    Have questions? Call us at 800-762-7846 (Mon-Fri 5am-7pm and Sat 6am-3pm PT) or send us a message
    Place your order by 3pm PT for same day shipping
    Copyright 1995-2014 SMARTHOME™
    Verisign Secure Site PayPal Acceptance Mark